Perry Machinery Czech Republic: +420 495 822 770 perryczech@perryczech.cz
Stock #HG59679
Used from low pressure boiler PV Roučka type VPP 1000, nominal heat output of 1160 kW. The boiler is equipped with a burner APH M-16 with an output of 1,400 kW. The boiler was manufactured in 1999, the torch was manufactured 1998 Kotel is sold including cabinets and control units. The boiler was in operation for approximately two years.
Location: Central Europe
Stock #HG59721
Used boiler made by Tipa model SPR 250. Maximum output rated 250KGS/hr. Max working pressure 7 MPA. Unit includes burner Wieshaupt WG 30N/1-C: rated power min 40 kW max 350 kW, the fuel: gas (25M3/H), pressure of fuel 2,3 KPA and control panel Limacon. Boiler operating time: 5040 hours. Boiler was made in 2004 and burner in 2003.
Location: SLOVAK REPUBLIC
Stock #HG59594
Used boiler made by Viessmann Vitoplex, model LS100. Capable of making up to 395 kg of steam per hour heating medium is gas. Including control panel and 2X pump.
Location: Europe
Stock #HG59629
Used boiler made by sigma Slatina, model VSP 1600. Capable of making up to 1600 kg of steam per hour, heating medium is gas. Boiler is new 1982. The boiler is offered including control panel, burner PRVNÍ Brněnská Strojírna Třebíč, TYP APH-M 25 PZ, water treatment plant. The machine has all the documentation.
Location: Central Europe
Stock #HG62349
Used Roučka Slatina model VSK 2,5-1 steam boiler. Capacity 1250 - 2500 kg of steam per hour, max working pressure 1,1 MPa. Includes Weishaupt oil burner, control panel and documentation.
Location: Central Europe
Stock #HG62465
Used Verner model Golem 1600 steam boiler. The unit consists of a bulk fuel tank and straw intake, conveying paths, burner G2500, combustion chamber, steam exchanger, exhaust fan with multi-cyclone separator, ash removal device, electrical switchboard and hydraulic unit for driving the sliding floor of the fuel tank and ash grate. - The burner has a rated output of 300 kW, an outlet temperature of 110°C (depending on the output), a maximum working pressure of 2.5 bar, a minimum calorific value of 9.13 MJ/kg, a maximum moisture content of 20%, fuel biomassl. - The NOX S 1800 D steam exchanger has a rated output of 1800 kW, outlet temperature 190°C (depending on output), maximum working pressure 12.5 bar, %, fuel flue gas.
Location: Europe
Stock #HG59630
Used boiler made by Sigma Slatina, model VSP 2500. Capable of making up to 4000 kg of steam per hour, heating medium is gas. Boiler is new 1983. The boiler is offered including burner PRVNÍ Brněnská Strojírna Třebíč, TYP APH-M 45 PZ. The machine has all the documentation.
Location: Central Europe
Stock #HG62445
Used LOOS (Bosch) model UL-S 4000 steam boiler. - Boiler has steam capacity 4.000 kg/hour, max allowable pressure 28 bar, max allowable temperature 230°C. - Includes gas burner New 1996, dismantled and ready for loading.
Location: Central Europe
Stock #HG59624
Used boiler made by PRVNÍ Brněnská Strojírna(Czech Republik). Capable of making up to 4000 kg of steam per hour. Heating medium is gas. Including control panel, new 1992.
Location: Central Europe
Stock #HG62444
Used LOOS (Bosch) model UL-SX 10000 steam boiler with economizer ECO 1. - Boiler has steam capacity 10.000 kg/hour, volume 16.400 litre, max allowable pressure 16 bar, max allowable temperature 204°C. - Economizer ECO 1 has maximal allowable pressure 31 bar, heat output 438 kW and maximal allowable temperature 238°C. - Includes gas burner New 2008, dismantled and ready for loading.
Location: Central Europe
Stock #HG62443
Used LOOS (Bosch) model UL-SX 16000 steam boiler with pre-heater. - Boiler has steam capacity 16.000 kg/hour, max allowable pressure 16 bar, max allowable temperature 350°C. - Pre-heater has maximal allowable pressure 16 bar and maximal allowable temperature 350°C. - Includes gas burner New 1996, dismantled and ready for loading.
Location: Central Europe
Stock #RG9928
(2) Used boilers made by Bono Energia in 2012, type CTD 65/25/320/SH/DO/ECO. Each boiler has a steam flow of 65 tonnes/hour at a pressure of 18.8 bar and temperature of 320 degrees Celsius. They are currently equipped with (2) GRC G1 burners each and are designed to burn light fuel oil. Sale includes auxiliaries, feed water pumps, primary air fans, thrust fans, valves , expanders , flue gas ducts, instrumentation and control system, supporting construction, stairs and platforms etc. Quotes will be issued for both boilers. Conversion to natural gas burners is possible.
Location: N/A
Stock #RG9965
Used steam boiler made in 2003 by VKK Standartkessel (Germany) with capacity of 40 tonnes/hour at a pressure of 17 bara. (2) boilers are available. Quotes will be issued for (1) boiler. Both boilers have had 4000 hours of use or less.
Location: Europe
Stock #V880-026
Used Pacific Boiler Feed Pump 2000 GPM Manufacturer: Pacific Boiler Rebuilt storeroom spare Size 8, 200 gpm 4430' head, 3580 rpm Hydro test 675/3300
Location: Midwest USA
Stock #UG6082
Used two stage burner by Oilon (Finland) type RP-130H, designed for work on diesel oil/heavy oil. Oil consupmtion in range 44-121 kg/h. Burner new 2007. Has a new pump and new servomotor.
Location: EU
Stock #UG6153
Second hand steam boiler by Clayton (Belgium) type EG-10-1 with working output of steam 157 kg/h at 10 bar pressure, and temperature 184°C. Boiler is heated by natural gase. Gase consumption 11.7 Nm3/h. Coil has working volume 24 l. Heating surface 4.5 m2. Burner power 107 kW.
Location: PL
Stock #AS60961
Unused steam boiler Alba (Turkey) type D05(1500). Designed capacity is 1500 kg of the steam per hour, maximum steam temperature is 204 degrees C, maximum steam pressure is 16 bar. Works on both Natural gas and Diesel. Natural gas consumption is 118 m3/hour (15 bar), Diesel consumption is 95 l/h. Electrical capacity 3.85 KW, Heating capacity is 1050 KW. Size parameters excluding burner - 1650 x 2850 x 2290 mm. Weight without burner 2500 kg.
Location: Europe
Stock #RG9920
Used LPV Caldaie Model CF2000 steam generator. Maximum output rated 2000 kgs/hour. Operating pressure at 11.7 bar.
Location: EU
Stock #RG9978
Used steam boiler with capacity 10 tonnes/hour made by Babcock Wanson in 1998 and shut down during 2019. Design pressure is 12kg/cm2 (approximately 12 bar / 170 PSI) and max operating pressure 10kg/cm2 (approximately 10 bar / 142 PSI). Fuelled by liquid biomass including animal fat, vegetable fat, bio-heating oils, fuel oil. System includes thermal oxidiser that reportedly burns at more than 850 degrees Celsius for longer than 2 seconds and meets European legislation for incineration. Equipment list:- 35m3 insulated and heated tank, fuel pump, burner, Babcock Wanson oxidation chamber, Babcock wanson recovery boiler (10 tonnes/hour steam production), induced draft fan, heat exchanger, purge tank, water tank, boiler feed pumps, steam collector, fireplace, control and auxiliary elements, control panel. Also available if required is the steam distribution equipment, which includes steam collector, piping, steam purge valves, steam flowmeter, etc.
Location: Europe
Stock #RG9863
Unused & uninstalled Ambitermo approximately 20,000kg/hour heat recovery steam boiler. Unit designed for: 73,440kg/hour of exhaust gas flow at 100% MCR Exhaust gas temperature at inlet 504 deg.c. Exhaust gas temperature outlet (after 2nd economizer) 143 deg.c (unfired) & 120 deg. (fired) Steam pressure rated 10 bar. Inlet water temperature before economizer 105 deg.c. Inlet water temperature after economizer 175 deg.c. Design pressure rated 10 bar. Boiler heat exchange surface area 1,430sqmt. Nominal boiler steam production is 12ton/hour (unfired) and 20ton/hour (fired). Steam consumption in de-aerator 0.75ton/hour (unfired) & 1.5ton/hour (fired). Burner required power for 20ton/hour (100%MCR) is 5.2mw. Equipment included as follows: (1) Single pass exhaust gas boiler, smoke tume type. Cylindrical horizontal body with welded tube bundle to the front and rear ends. Boiler is mounted monobloc on a profile frame. (1) Eclipse post-combustion duct burner, rated 5.5mw for 20ton/hour steam with 75% MCR output. Modulation 1:8 (1) Primary economizer (1) Secondary economizer (2) Feed water pumps Various valves and instrumentation (1) Metering system (1) Exhaust gas duct and by-pass system. (1) Deaerator rated for 20ton/hour, design pressure at 0.5 bar, design temperature 110 deg.c. (1) Drain tank, 1cumt capacity. (1) Exhaust gas stack.
Location: Europe
Stock #RG8900
(2) Used boilers with capacity 30 tons/hour each made by ISGEC John Thompson in 1993 and shut down in September 2008. Fueled by LSHS (low sulphur heavy stock) / fuel oil. Working pressure is 34 kg/cm2 (33 bar or 484 psi). Control panels, burners, valves, mountings, steel construction and chimney are included. Boilers weigh approximately 200-250 tons each. Full details available on request. Quotes will be for (2) boilers.
Location: Asia
Stock #RG8882
Used bagasse fired bi-drum water tube boiler made by Walchandnagar Industries limited in 1988. Main characteristics as follows: - maximum continuous rating is 32 tph (70,550 PPH), peak rating 35.2 tph (77,600 PPH). - steam pressure at oultet of main stream stop valve is 32 kg/cm2 (31.38 bar or 455 psi), design pressure is 40 kg/cm2 (39.23 bar or 570 psi). - final steam temperature 380 degrees Celsius +/- 15 degrees. - hydraulic test pressure 60 kg/cm2 (58.84 bar or 850 psi). - feed water temperature at economizer inlet 85 degrees Celsius. - type of grate : traveling. - ash disharge : bottom. - grate drive mechanism : hydraulic drive. - heating surface: furnace 265 M2, boiler bank 720 M2, super heater 131 M2, economizer 359.52 M2, air preheater 850 M2. Quotes will be for (1) boiler, but (2) are available.
Location: Asia
Stock #V21600-30
Used Bigelow boiler #1 - 100,000 pounds of steam per hour at 300 psig and 480°F superheated, with Dennis Detrick type furnaces in order to facilitate start-ups with firewood. The fan has a run armature shaft and can be moved by a turbine 200 hp Worthington and an electric motor. The forced draft fan is driven by an electric motor 100 hp. Produces 100,000 pounds of steam per hour at 300 psig and 480° F.
Location: GUATEMALA
Stock #RG8883
Used 70 TPH (154,000 PPH) coal fired water tube boiler made by John Thompson with a working pressure of 30 kg/cm2 (29.42 bar or 430 psi).
Location: Asia
Stock #V21600-31
Used Boiler #2 Babcock & Wilcox repowered with engineering HRSG of Mexico, plus a second repowering took place in 2012. Produces 200,000 lbs of steam per hour at 600 psig, 750°F superheated currently operating at 450 psig to supply steam to current turbogenerators. This boiler has an inclined pin-hole type grill. The two forced draft fans are driven by electric motors 150 hp. The induced draft fan, brand Armee-Babcock. It has a capacity of 265,000 cubic feet of air per minute and is driven by a turbine 1000 hp and respective reducer.
Location: GUATEMALA
Stock #ZG63352
UNUSED 250TPH Bagasse/Biomass Boiler Manufactured by Triniton Brazil. Model: Pin Hole Grate , Top Support, Capacity: 250 TPH (550,000 PPH) Max. Working Pressure: 1500 PSIG (103 bar). Steam Temperature” 1000 ° F (540 ° C) Efficiency (as fired): 73.45 Fuel: Bagasse (can be converted to burn other biomass). Fuel Consumption: 239,907 lbs./hr(108.82 TPH). Based on Fuel LHV 3,214 btu/lb(1,785 kcal/kg), 50% Moisture Content. Scope of Supply: Boiler with Associated Equipment, Fans, Pumps, Instrumentation, ESP HISTORY: Manufactured: 2021/2022 Stored in Original Factory Shipping Crates.
Location: North America
Stock #ZG694-2581-1
Used Finn Aqua model 1500-S-1 pure steam generator. Single still with pump.
Location: Midwest USA
Stock #ZW62458
Used TFU (Turboflow) Biomass Boiler rated at 55 Tons/Hr at 60 Bar and 450°C. The boiler was built in 2012 and was burning a combination of logs and wood chips. The boiler has a fixed grate and consumes approximately 10 tons of fuel per hour.
Location: South America
Stock #ZG63715
Used Superior Model 8-5-750 Packaged Steam Boiler Manufacturer: Superior Boiler Works Inc Capacity: 5175 lbs/hour steam Natural gas 150 HP 150 psi 759 square foot heating surface Built 2014 NB #17738
Location: West Coast USA
Stock #ZW62631
Used 2003 120,000 Lb/Hr Nebraska D-Type Watertube Package Boiler Model NSX-G-100, with MAWP of 250 PSIG. Boiler equipped with Low Nox Natural gas burner, Economizer, Stack, Structural Steel, boiler feed water pumps and ancillary equipment. Boiler is in excellent condition, with all available documentation and drawings.
Location: West Coast USA
Stock #ZG61124
Used gas fired boiler rated 650 psi @ 470°F. Skidded, natural gas fired single burner. Previously used in methanol plant.
Location: South USA
Stock #ZG62874
Used 2009 Hurst Model: Hybrid, 2 Pass Waste Fuel. Boiler Rated at 51,750 lbs./hr, MDWP 450 psig Operating Pressure 400 psig, Steam Temperature 600 ° F, Heating Surface Sq. Ft 9750. Fuel: Wood chips or Waste Wood. Fuel Consumption:18,248 lbs./hr. of Wood Chips based on 5652 btu/lb, ≤30% Moisture Content. Scope of Supply: Hurst Steam Boiler, Fuel Bin, Fuel Conveyor, Metering Sin, Solid Fuel Burner with Natural Gas Starter Burner, Trim Reciprocating Grate Stoker, Wet Ash Conveyor, Fly Ash Collector, Stack, Air Fan Twin City 30 Hp 460 Volt with VFD, Flue Gas Recirculation Fan Twin City 20 Hp 460 Volt with VFD, Metering Screw Motor 7.5 Hp 460 Volt with VFD, Reinjection fan 1.5 Hp 460 Volt with VFD, E-Tech Economizer E-tech Superheater ID Fan 250 Hp 460 Volt, Soot Blower, Deaerator 100,000 PPH, 50 psig Boiler Feed Water Pumps, and Boiler Building.
Location: South USA
Stock #ZG63030
Nationwide Boiler’s low NOx 60,000 pph, 680 psig design (250-600 psig operating), superheated steam, trailer-mounted package watertube boiler is set to burn natural gas or #2 oil. It is fully piped and wired and includes the following components: Low NOx Burner EconoStak Economizer Burner Management System Single-point Positioning Combustion Controls Forced Draft Fan, Motor & Starter Complete Fuel Train & Pilot Ignition System #2 Fuel Oil Pump Water Column & Site Glass Steam Pressure Gauge Low-water Cutoffs Safety Valves Feedwater Stop & Check Valves Blowdown Valves Continuous Blowdown Metering Valve Chemical Feed Valve Single Element Feedwater Regulator with Pre-piped 3-Valve Bypass Steam Non-return Valve FGR Ductwork Stack (loose) NEMA 4 Electrical Enclosures Low NOx CataStak™ SCR System (optional) Weatherproofed (except for freezing) Meets FM, NFPA 85 & IRI Insurance Standards Operating Manuals
Location: Midwest USA
Stock #ZG58743
75,00O#/hour. Optimus O-type shop assembled packaged watertube boilers, 750 psig design @ 750°F, final steam temperature capable of operating at pressure between 350 to 675 psig. Built in accordance with ASME code and bearing NB stampings. Each unit is equipped with a Todd Variflame low NOx fully automatic burner for gas or #2 oil firing including fuel trains, forced draft fan with 150 HP TEFC electric motor drive 3/60/480V with starter, Fireye E 110 microprocessor based flame management system to I.R. I., F.M., U. L. ,N. F.P.a. Requirements, Moore micropressor combination combustion and feedwater control system, and a 480V/L20V control circuit transformer. Additional trim components consist of: 2 1/2" feedwater control valves with 3 valve bypass, feedwater stop and check valves, water column with water level probes, gage glass, auxiliary float type low water cut out, 1 1/2" continuous blowdown control valve and stop valve, (1) 3/4" chemical feed valve,1 1/2 " blowdown valves, vent and drain valves, Desuperheater,safety valves and 8" main steam non return valve, as well as miscellaneous valve trim. Also included is a 4 8 X 10 ft. High stub stack. The boiler assembly is mounted on a special designed multi-axle drop-deck trailer.
Location: USA
Stock #ZS61053
Unused 50 TPH boiler "BEM" model E-50-3.9-440. Steam pressure - 39 ATI (3.9 MPA). Steam temperature - 440°C. Designed for oil and gas.
Location: ASIA
Stock #ZS60718
Used Foster Wheeler biomass boiler. Used with wood chips, capacity - 55 tons per hour at 450°C. Outlet pressure 42 ATI. Surface boiler: 1321 square meter. The boiler was refurbished in 2008.
Location: BRAZIL
Stock #ZG62031
Unused 150,000 PPH Nebraska model N2S-7S-89 shop assembled package watertube boiler, 350 DP. Type “A” design. Equipped with a Natcom low NOx 30 ppm package burner for natural gas/#2 oil firing, free standing forced draft fan with 400 HP motor, Fireye flame safeguard system, fully automatic Siemens combustion and feedwater control system. Built in accordance with ASME code and bearing NB & HSB stamping. Boiler equipped with all relating boiler valve trim, and controls. This boiler is shipped by rail only. Built end of 2014.
Location: Midwest USA
Stock #ZG63683
UNSED, never installed Cleaver Brooks 250,000 lbs/hr Industrial Watertube Boiler - Model NB-801D-125-550-AL-LH - Serial CP-4582 - D-type watertube style - Pressure 420 psig operating pressure (superheated, temp 650F +/- 25) - Natcom LoNOX Burner, natural gas. Gas train included. Burner model NCB-330-68A-000-S10-000 - Stack included - 3 sections - Economizer, ECO vertical - Dimensions: 79' diameter X 56' long - Controls - 2 plc's + burner management + combustion controls - Includes SCR for emissions reduction - Built 2019 - Under nitrogen purge with desiccant in furnace area
Location: Midwest USA
Stock #ZW58801
Used Babcock and Wilcox black liquor recovery boiler for 500 tons of dry solids of black liquor. Flow rating 500,000 #/hr. Operating pressure 800 psig. Unit is still installed and can be inspected and is being sold with all technical data and accessories. New in 1987.
Location: Canada